Automatic firmware updating

TO UPDATE TO THIS VERSION YOU NEED VERSION 2.01.0020 OF DIGIRACE-MMX, FIRST DOWNLOAD THE LATEST VERSION OF DIGIRACE-MMX AND THAN PROCEED UPDATING THE FIMWARE. By version 1.91, to pair Corsaro with PC, activate the Discoverability in Corsaro Bluetooth menu.

-Implemented new automatic firmware update for WID-A modules. -Activated the optional Inertial Pack management for Lean Angle and Longitudinal and Lateral accelerations.

-Introduced user notification function: low voltage for main battery and WID modules or other system alerts. 1- Management of the archive with the coordinates of the finish lines of the main world tracks loaded in Digi Race-LE 2-The Management of customised finish lines added with the possibility of entering the coordinates acquired from Google Earth. (Starlane Enhanced Precision Laptiming Algorithm)feature: a new laptiming algorithm allowing very hi laptiming precision also in conditions of not good data on the official GPS signal.

-Implemented display minimum and maximum peaks visualization at the end of session. - Indication of frequency and ratio measured while learning the gear on Athon GPS-RW and PRO.

-Activated library with more than 200 tracks with finsh line and intermediates, divided for cathegory and country, which Corsaro will find out automatically but you can also select them manually. -Implemented new Open Circuit and Performance Test features for hill climbing, rally and acceleration races. -General optimizations.-Added main battery status and WID-A battery status to the access screen. -Implemented display of the Active Circuit on the access screen with quick access to the Track selection. -Implemented management of WID-B and WID-C wireless modules which will be released soon.

-Introduced compatibility for WID-B and C modules for: Aprilia RSV-4 APRC, BMW S1000RR, Ducati Panigale, Kawasaki ZX10 2011-20, Yamaha R1 2015. -Implemented the minimum and maximum Exhaust Temperature and maximum RPM indication when passing the finish line. -Introduced new feature SGB (Starlane GPS Booster). -Introduced selection of user specialty to set the default profile with the best performance for Kart / Scooters, Car / Motorbike or Nautical.

Try this first: Go to Device Manager (Instructions are above), scroll down to Smart Card readers, right click the CAC reader that shows up below Smart Card Readers. Hit OK, then select Extract (lower right corner of this window).

NOTE: If you don't see it, you can also click Start, In the Start Search line type in: If it did not install correctly... It will prompt you for a name for the folder (type in CAC Driver).

To be used only with Digi Race MMX 2.01.0009 or higher version. THE SAFD-2 FUNCTION CAN BE ACTIVATED BY PRESSING FOR 2 SECS. -New GPS management by now working at 10Hz instead of 5. -Introduced the innovative feature SAFD (Starlane Automatic Finish line Detection) developed by Starlane to allow the automatic finish line positioning on the main straight without any operation by the driver, also on unknown tracks. ATTENTION: AFTER THE UPDATE IT'S NECESSARY TO RUN THE "FORMAT MEMORY" COMMAND IN ATHON "MEMORY" MENU. -Modified intermediates visualization on the run: is now displayed the gain/loss in comparison with the personal best performance in the same track point during the current session.

-Important update with fixes and general improvements. -New feature SAFD-2 with the revolutionary automatic intermediates detection. -Extended range setting for analog calibrations on RID modules. -General improvements and fixes in RID modules management -Updated support for RID Kart expansion module -General improvements in RID modules settings -Introduced support for RID Moto and RID Analog-3 expansion modules. -Minor enhancements in session storage and in Best Lap Number reference. (Starlane Enhanced Precision Laptiming Algorithm) feature performance. The SAFD feature is accessible in the menu: GPSFINISH LINE DETECT.

-Activated the Inertial Pack for Lean Angle and Longitudinal and Lateral accelerations.

TO UPDATE TO THIS VERSION YOU NEED VERSION 2.01.0020 OF DIGIRACE-MMX, FIRST DOWNLOAD THE LATEST VERSION OF DIGIRACE-MMX AND THAN PROCEED UPDATING THE FIMWARE. By version 1.91, to pair Corsaro with PC, activate the Discoverability in Corsaro Bluetooth menu.

Leave a Reply